カテゴリコンピュータ周辺機器ネットワークイーサネットハブ状態傷や汚れあり（詳細）hp TippingPoint 1400N商品構成HP Tipping Point 1400N初期化済商品状態************************************Booting XLR from Flash
=======> Starting spd <=========================================================================================
TippingPoint Technologies, Build: 53.0
Compiled on Mon Mar 19 15:38:46 MST 2012 by builder@TPBuild1.austin.hp.com
================================================================================
----- Configuring DRAM Channel 0 -----
Memory channel operating at 666 MHz data rate.
Amount of memory available on channel 0: 4096 MB----- Configuring DRAM Channel 2 -----
Amount of memory available on channel 2: 0 MB
Please wait for ECC setup.Enter 'TEST' to run Memory Test.Booting from DRAM
............................Done.
Detected CPU Rev B2 [Revision ID 0x4]
Detected CPU XLR308 [CPU ID 0x6]
CPU Frequency = 1000.000000MHz
Total Available Ram = 0x3f00000, Total Heap Size = 0x3d87400, stackbase = 0x8c1fdfc0
All 8 cpus successfully started
done
HSCFC Image: 0x2C
HSCFC Product Version: 0x0
Boot: Hardware watchdog has not triggered.
Boot: ACTIVE is selected.
Initializing disk controllers...
Found SYSTEMF_1 disk
Model: SMART CF
Firmware: 20091110 Serial#: 20101220055A408B408B
Capacity: 1953.9 MB = 1.9 GB (4001760 x 512)** Communication error **Locking down commands
ZFCP Version:4
ZFCP Misc Status/Control Register: 0x88Booting in 5 units. Press Ctrl-C to halt...Booting in 4 units. Press Ctrl-C to halt...Booting in 3 units. Press Ctrl-C to halt...Booting in 2 units. Press Ctrl-C to halt...Booting in 1 units. Press Ctrl-C to halt...
Inflating image:................................................CompletePrepared Segment Map for Kseg0 Mode.
[SEGMENT 0]
Is Segment Shared ==> 1
P_Vaddr 0x80300000, P_paddr 0x80300000, MemSz 0x1700000, FileSz 0x12f36d4, Align 0x1000
xlr_lib_copy_image_32 i=0
cpu_online_map=ff, userapp_cpu_map ff
psb_os_active_mask=0, psb_os_mask=0
boot1_info: userapp_cpu_map=ff, psb_os_cpu_map=0
cpu_online_map = 0xff
Jumping to the application... 0x80300000
------------------------------------------------------------
ataCtrlReset taskDelayataCtrlReset taskDelay0 ataCtrlReset taskDelayataCtrlReset taskDelay1 ataCtrlReset taskDelayataCtrlReset taskDelay2 ataCtrlReset taskDelayataCtrlReset taskDelay3 ataCtrlReset taskDelayataCtrlReset taskDelay4 Initializing PCIPCI - MEM=0xd0000000 size=256MB HT - MEM=0x0 size=0MB
PCI - IO=0x10000000 size=64MB HT - IO=0x0 size=0MB
PCI - CFG=0x18000000 HT - CFG=0x0
Configure tlb virtaddr=0xffffffffd0000000 size:=0x8000000
End bus: PCI=255 HT=0
Target Name: vxTarget
Initializing MIB2 interfaces
Initializing MIB2 IPv6 interfaces
Attaching interface lo0... done
xlrMacInit for mac device 0
GMAC0 phy addr is 0x15
pde bucket_map = 10
BUCKETS AVAILABLE..........
Bucket[0] = 4
xlrMacInit for mac device 1
pde bucket_map = 10
xlrMacInit for mac device 2
pde bucket_map = 10
Attached IPv4 interface to xlr unit 0
Attached IPv6 interface to xlr unit 0
devName: xlr, addr: 0.0.0.0
net.inet.udp.blackhole: 0 -> 1
net.inet.tcp.blackhole: 0 -> 1Adding 43582 symbols for standalone.
CPU: Raza Microelectronics Initialize Memory.......................[OK]
Add reboot hooks........................[OK]
Start CPU Resource Monitoring...........[OK]
Initialize System Clock.................[OK] 2021-08-19 01:28:14 [UTC]
Set Boot Time...........................[OK]
CPU Speed...............................[OK] 999 MHz
Identify Host Type......................[OK] Z1M
Identify HW.............................[OK] 5 bcom
ataXbdDevCreate: ERROR- Device 0 on Controller 0 not installed
Initialize LCD Panel....................[OK]
Mount File System.......................[OK]
Mount Removable File System.............[OK]
Initialize IPC..........................[OK]
Initialize Paths........................[OK]
Read Configuration Files................[OK]
Apply Task Environment..................[OK]
Apply LCD Environment...................[OK]
Create /ramLog..........................Formatting /ramLog for DOSFS
Formatting...OK.
[OK]
Create /ramTmp..........................Formatting /ramTmp for DOSFS
Formatting...OK.
[OK]
Initialize System Log...................[OK]
Initialize Audit log....................[OK]
Initialize Security.....................[OK]
Initialize License Manager..............[OK]
Initialize Update subsystem.............[OK]
Install DV..............................[OK]
Create /ramRO...........................Formatting /ramRO for DOSFS
Formatting...OK.
[OK]
Load RAM Disk...........................[OK]
Preparing SSL certificates..............[OK]
Set Memory Protection...................[OK] 0xb7cf5740
Performing Host/Model Checks............[OK] Software chassis
Initialize Board Flash..................[OK]
Locking down bootloader commands
Bootloader lock already set
Initialize Network Processor............[OK]
HW Descriptor...........................[OK] 78:ac:c0:ef:7a:e4
Ungraceful shutdown.
Read TOS metadata.......................[OK] ver=3.8.0.4342
Read DV metadata........................[OK] ver=3.2.0.9549
Deflating...............................[OK]
Initialize Block Log....................[OK]
Initialize Alert Log....................[OK]
Initialize Quarantine Log...............[OK]
Initialize Keys.........................[OK]
Initialize SNMP.........................[OK]
Initialize Email........................[OK]
Initialize Remote Syslog................[OK]
Validating Certificate..................[OK] __________